Gluing UHMW Plastic - FineWoodworking
2007年4月9日 · Without the flame treatment, the bond between the wood and the plastic as well as between plastic to plastic was easily broken. With the flame treatment, it seems very solid. 3M 4693H will bond to UHMW. I used it to glue the runner onto one of my crosscut sleds, ans have used it to glue things to 5 gal. poly buckets.
Gluing HIPS (High Impact Polystyrene) - Eng-Tips
2006年11月16日 · Regards, Cory. Please see FAQ731-376 for tips on how to make the best use of Eng-Tips Fora. Pud (Mechanical) 16 Nov 06 13:13. Cyanoacrylate adhesives - choose your curing speed and required viscosity and off you go. Talk to manufacurer's - eg Loctite (only one I know I'm afraid! - we use their Grade 406 for ABS - works a treat) Cheers.
Gluing clear acrylic to ABS - Eng-Tips
2007年1月26日 · We use a lot of Loctite products and the rep left a sample of the Loctite® 3030 Plastic Bonding Adhesive for us to try. We ultrasonic weld most if not all our plastic components but the Loctite® 3030 Plastic Bonding Adhesive has proved to be a worthy alternative. Best Regards, Heckler Sr. Mechanical Engineer SWx 2007 SP 2.0 & Pro/E 2001
How to Glue and Clamp a Picture Frame - FineWoodworking
2012年8月7日 · In this introductory video you'll get an overview of how to make beautiful frames for your art. Get accurate miters every time with this custom tablesaw sled. Two distinct frame designs that can be made using your router table. Gluing up a picture frame can be tricky.
Best Glue for Bent Laminations - FineWoodworking
2007年5月1日 · A: There isn’t one adhesive ideal for every application. With domestic wood laminations, the simplest and least visible glue is PVA (polyvinyl acetate) yellow glue. Unfortunately, it is not particularly rigid and does not have much open time. Adding a maximum of 8% powdered cornstarch by volume makes the glue more rigid and controls springback.
Which Glues Work in Cold Temperatures? - FineWoodworking
2010年1月1日 · Gorilla Glue polyurethane can handle 40°, but the cure time also is slower. The bottom line: Use Gorilla Glue down to 40°F and Titebond III down to 47°F, but the best solution is to heat your shop a bit. Everything will be easier then. Too cold to bond. Most yellow glues should not be used below about 55ºF.
Stress-free veneer glue-up - FineWoodworking
2022年7月26日 · Use a good amount of glue, but not so much that when you hold it upright it drips. The bigger the piece the more cauls and clamps you will need. I suggest starting small and getting the hang of it. Leave the piece clamped up for approximately 8 hours. Gluing veneer to a substrate adds one layer of glue and one layer of wood to one side.
Suitable adhesive to bond wood to ABS - Adhesives & sealants
unclesyd (Materials) 6 Nov 08 00:04. Two things that I've seen used with light loads are the IPS Weld-On ABS cement in the plumbing dept. I have also seen structural adhesives like Liquid Nails used. One epoxy for the epoxy option. B-45TH This is a 2 part flexible epoxy.
What fasteners work best with MDF? - FineWoodworking
2005年8月21日 · Assuming you'e talking about 3/4" MDF, biscuits with glue will work fine. You can clamp the case to keep everything together until the glue dries, but it is simpler and faster to use a few nails instead. Even nails with an air gun will raise the surface fibers slightly, so it is a good idea to sand them smooth before you fill the nail holes.
What Glue for Bending - FineWoodworking
2007年1月19日 · To reduce springback and use your existing form, you could use 1/8" bending plywood. By running the inner layers cross grain, with staggered joints, and using a cold press glue like Unibond, the joints will help reduce the pull. Make sure you leave it in the form long enough for the glue to completely cure.