Chevrolet Silverado: Which Axle Ratio Do I Have?
By Mark Garrett - July 1, 2015. This article applies to the Chevrolet Silverado GMT800, GMT900, and K2XX (1999-Present). Axle ratio refers to how many times the driveshaft turns to make the wheels turn one revolution. If you think of it in extremes, a 2.00 axle ratio means that the driveshaft turns two times for every one revolution of the wheels.
VIN Decoder - Chevrolet Forum - Chevy Enthusiasts Forums
Indicates the model year of the vehicle (e.g. B:1987 or 2011). Must sometimes be read with postion 7 in the VIN, in order to make an accurate determination. The plant in which the vehicle was manufactured. The code varies with each manufacturer. These last six digits are used to identify a specific vehicle within the border Year/Make/Model class.
Silverado, Sierra & Fullsize Pick-ups - Chevrolet Forum - Chevy ...
2024年10月2日 · All times are GMT -5. The time now is 5:09 AM. Silverado, Sierra & Fullsize Pick-ups - Chevrolet Silverado/GM Sierra forum for latest news, discussions, how-to guides, and technical help. Platform: Truck, GMT 400, 800, & 900.
Chevrolet Silverado 1999-2006: How to Replace Oxygen (O2) …
2015年6月17日 · Step 2 – Install the new O2 sensors. Hand-tighten the new O2 sensor into place. Use the 7/8" Crescent wrench to tighten the O2 sensor to a snug fit. Reconnect the wire harness to the new O2 sensor. Route the wire harness to the …
Chevrolet Silverado: Brake Diagnostics Guide | Chevroletforum
2015年7月9日 · A soft brake pedal is typically the result of a hydraulic fluid leak in the braking system. Check the brake fluid level in the master cylinder, also known as the brake fluid reservoir. If the brake fluid is low, a leak is to blame for your soft brake pedal. If you don’t notice pools of brake fluid underneath your truck, top off the reservoir ...
Chevrolet Silverado 2007-2013: How to Replace Oxygen Sensors
2015年6月8日 · Step 2 – Disconnect O2 sensor from exhaust. Identify the faulty O2 sensor from the code. Bank 1 is on the driver's side, while bank 2 is on the passenger's side. Sensor 1 comes before the catalytic converter, while sensor 2 comes after. Once you've identified the correct sensor, you can get to work.
Chevrolet Silverado 2007-2013: How to Change Oil
2015年6月4日 · Step 7 – Reset oil change warning light. Turn your ignition key to the "Run" position with the engine off. Press and release the gas pedal three times within five seconds. The system is resetting if you observe the "Oil Life Reset" message display for 10 seconds. Turn off the ignition key to the lock position.
Chevrolet Silverado 2007-2013: What Are Signs of a Bad …
2015年7月21日 · This article applies to the Chevrolet Silverado 2nd Generation (2007-2013). If your transmission isn’t acting right, its undesirable behavior could include one or more of the following: Taking too long to shift; the engine revs higher than normal RPMs before a shift happens. Making hard shifts, which occur with a noticeable clunking noise and ...
Chevrolet Silverado 1999-2013: Why is My Instrument Cluster …
2015年7月13日 · Step 1 – Perform an instrument cluster test. This test will verify what on the cluster is working and what is not. Simply turn the key to the "on" position and watch for all the warning lights to illuminate. Some Silverados may perform a "needle sweep," which moves all the gauge needles from right to the left.
Chevrolet Silverado 2007-2013: Transmission Problems and …
2015年8月4日 · No 1st or 4th gear (in Drive it shifts from 2nd to 3rd and locks the torque converter): Shift "A" solenoid has failed. Wiring problem from the PCM to the transmission. No 1st or 4th gear (torque converter doesn’t lock, can be driven in 2nd, 3rd, and Reverse gear): Transmission is in “limp home” mode or lost electrical power.