Staining oak plywood - Woodworking Talk
网页2013年9月23日 · 57 posts · Joined 2013. #1 · Sep 23, 2013 (Edited) I am having an issue with staining some oak plywood. I am using Minwax red mahogany stain on a nice grade oak plywood. The problem is that on test pieces the stain looks great until I tried it on a piece that was sanded too 220. On the sanded portion the stain isn't as dark and there are ...
Need help staining maple plywood - Woodworking Talk
网页2021年8月30日 · 2. Mixed seal coat with denaturalized alcohol in a 50:50 mix and applied on plywood and wiped away. 3. Waited for 20 mts and lightly scuff sanded with scotch Brite. 4. Applied the stain coat and wiped away. I am now going to wait 24 hours to come back and apply seal coat followed by laquer.
Staining oak veneer on plywood - Woodworking Talk
网页2015年3月23日 · your plywood is the key I used some el cheapo depot plywood on this otherwise quality Mission headboard made with quartersawn Oak. The front and back are completely different colors but the stain was the same. The issue is that the veneer is so thin the stain doesn't penetrate well, stops at the glue bond and you have an problem.
Staining Birch Plywood - Woodworking Talk
网页2013年8月30日 · A pickle finish is using a paint where the pigment sticks in the grain of the wood and details like moldings or carvings. Since birch is a closed grain wood there is no grain for the pigment to stick into. All of the flat areas between moldings would be without the character of the pickling. That is why the open grain oak is normally used for ...
Sanding plywood to stain - Woodworking Talk
网页2014年3月24日 · After the filler dries overnight there may be places where there is a haze. This should be sanded off with a light sanding. Then the wood is ready to finish. The plywood you are using will be prone to blotching so you might use a wood conditioner prior to staining. This will allow the stain to go on more uniform.
Staining oak plywood - Woodworking Talk
网页2007年7月21日 · A trick to help it absorb more stain is to water pop it. What you do is take a rag and get it wet with water. Wring out all the water then rub the damp rag over the surface of the plywood until it looks damp. This will open the grain and let more stain soak into the pores. Do one thing at a time, do it well, then move on.
Staining plywood - Woodworking Talk
网页2011年10月27日 · You might look closely at the edge of the plywood. I'm thinking the grade of plywood you are using may have veneer on the back side where stamped that is very thick. You may be able to use some coarse sandpaper on a orbital sander and quickly remove it without sanding through. Then sand again with finer paper.
Finishing Oak Plywood - Woodworking Talk
网页2011年5月4日 · You might want to very lightly sand the bare plywood with 150x-180x with a ROS, or a block sander sanding with the grain direction. Be very careful, as the face veneer is very thin. This sanding is just to clean up the face and remove handling marks. Use the stain of your choice, but don't sand. Apply your topcoat.
best kind of plywood for staining? - Woodworking Talk
网页2010年1月2日 · A forum community dedicated to professional woodworkers and enthusiasts. Come join the discussion about shop safety, wood, carpentry, lumber, finishing, tools ...
Birch plywood staining question? - Woodworking Talk
网页2011年12月5日 · 2) I've stained the box onyx (more on that later) 3) I plan on painting the MDF baffle black. Box built and baffle glue edges taped so glue joint will still adhere: These were sanded to 220 with a 4" flat sander, then I used 400 grit with hand block in grain direction. I did put per-conditioner on.