Tork Tech Terminator Install | SVTPerformance.com
Feb 4, 2012 · Here is a link for the Tork Tech Terminator kit. Terminator GT Kits for the '99-04 GT - Tork Tech. This kit, as outlined on the website. Only consist of the necessary components to get the Factory 2003-2004 Terminator Cobra Eaton M112 to bolt up to our PI 4.6 two valve Engines and drive it with a pulley system.
Tork Techs eaton swap on 2V....opinions?? - SVTPerformance.com
Sep 9, 2009 · This will allow me to run a ported eaton for awhile then down the road add the 03-04 Cobra's Kenne bell 2.8LH with ease. All are straight swaps. So I think the Tork Tech is a great idea because it gives you the ability to run an Eaton M112, Magnason MP112, Kenne Bell 2.2L, 2.4L, 2.6L, 2.8L, Whipple 2.3L and 2.4L, Vortech 2.3L, and 3.3L.
Tork Tech 2v conversion - SVTPerformance.com
Sep 3, 2009 · Vancouver, WA. The Tork Tech kit with some Stage I Fox Lake heads and Stage II cams, at 18 lbs of boost is putting down about 590-600 rwhp. As far as Tork Tech going under, they are backed by a couple of other businesses that have been around for about 15-20 years, so I doubt that would happen. Sep 3, 2009. #20.
Tork Techs eaton swap on 2V....opinions?? - svtperformance.com
Feb 3, 2013 · Savannah, GA. In '99 I installed the original Saleen Series 1 Eaton M90 kit on the stock 2V. Very similar to the Tork Tek kit. With the non PI heads and the canned Saleen tune it made 270 RWHP and 400LbFt of torque. I later added prted heads and a custom tune and was making 350whp on a mustang dyno.
Tork Tech Terminator Install | Page 2 | SVTPerformance.com
Feb 4, 2012 · The IAT sensor port needed to be blocked off as well because on the Tork Tech Terminator kit…its relocated to the lower intake. I simply cut the “nipple” off of the fitting. Tapped it with a 3/8” tap. Then threaded a cap screw in it. I also coated it with RTV sealant just to make sure I got it sealed up.
Tork Tech supercharger kit ...never installed, almost complete.
Oct 9, 2017 · Tork Tech intercooled kit (all hardware, pullies, etc is still in original packaging from TT) Eaton M112 Terminator SC with inlet, stock TB, and dump valve (20k ish miles) Ford Racing 47# injectors with FRPP plug adpaters. JLT Short Ram intake (painted comp orange) SCT BA2600 MAF. Ford Motorsport IAT.
4.6 2V Tork Tech members - SVTPerformance.com
Mar 19, 2016 · Feb 1, 2012. Messages. 2,689. Location. Indiana. My car makes 400/431 with the normal 7” Tork Tech lower pulley and a 3.1 upper pulley, unported Eaton and has stock exhaust manifolds. The car makes 11 pounds of boost, is tuned very conservatively with an 11.6 AFR and only 13 degrees of timing. There is a whole lot more left in it.
Introducing the first 2v GT with a 3.4 Whipple!
Sep 19, 2012 · PBG FL. Im proud to show you this around. Some of you might remember my car as the one with the MP112 Tork Tech kit. We used the same kit as the bases for the install. The only adjustment we had to make was to my hood. A small knoch was cut into the first layer of the fiberglass to clear the blower pulley. The rest fit perfectly.
Ordered a Tork Tech Blower - Who else has one?
Mar 5, 2009 · Lonnie @ blue oval chips tuned a tork tech kit that was on an 01 crown victoria, car put down 400rwhp. Both the owner and the tuner said the kit is a very good kit, infact he is selling tork tech's now and is helping them develop a kit for panthers. You wont be disappointed
Tork Tech Pulley Size Help! - SVTPerformance.com
Jan 8, 2013 · Im planning to run a 2.7 pulley this summer when I order my tork tech kit, but im doing a ported eaton.... 400 is easy to do with low boost. Pretty sure you could almost do that with a lil smaller pulley than stock. a 2.76 on a ported eaton is going to be way more than 400, hope you have good internals.