HDO and Exa/c plywood? - Woodworking Talk
2011年8月14日 · HDO and Exa/c plywood? Jump to Latest 3K views 5 replies 4 participants last post by mdntrdr Aug 14, 2011
Best wood for an outdoor sign (3'x5') - Woodworking Talk
2009年7月16日 · I have pulled signs out of ditches and canals and they were fine. I last bought some in 2004 or 2005 and it was like $35 a 3/8"x4'x8' sheet. Some lumber yards will carry it but if you have trouble call a sign supply company they get it in 4x8 and 4x10 sheets and it may be cheaper there if they will sell it to you. The pre-cut letters wood work ...
How to stabilize old dresser? - Woodworking Talk
2021年9月8日 · Plywood is certainly a viable option even a 1/4" sheet fastened over the existing back would work. Glue blocks will help if there is any movement along the tenons or panels, but ultimately a solidly fixed back is what gives a dresser its strength.
Screws in plywood edge? - Woodworking Talk
2023年3月11日 · Clamp the plywood securely to prevent ply separation. Using a nice sharp bit, drill out a 1/2" hole slowly letting the bit cut the wood (keep the bit from gouging into the wood quickly as it will try and "screw" itself into the wood because of the bit's flutes and lands).
Are there minivans that are big enough for 4x8 plywood?
2011年7月8日 · First of all, the interior of the van was just hair short of being 48” wide. So I was able to lay the plywood down flay on the floor, but only after scratching some of the interior walls and chipping off the edge of the plywood a little. Well, it wasn’t big of a deal. Well then, the real problem was that the van was not log enough for the ...
Ripping 4 x 8 sheets of plywood - Woodworking Talk
2011年1月3日 · I stored my plywood flat on a rack, when I pulled the plywood out it would rest it on a roll around that was lower than my tablesaw. I would roll the plywood up to the saw, rest one end on the saw, pick the end of the plywood up and kick the roll around in toward the saw and it would be mostly out of the way as I cut the plywood.
Formica laminated to Plywood vs MDF - Woodworking Talk
2019年12月20日 · If you are worried about it sticking ok, it will stick just fine except for the edging. I personally would use a strip of solid wood for a edge backer. The hpl will stick much better to solid wood edge backer than on either plywood or mdf. I always double coat the edging on both the hpl and the wooden edge.
How to prepare sanded plywood for painting | Woodworking Talk
2016年9月19日 · A lot depends on the plywood and how glossy you plan to paint them. Sanded plywood is usually pine and sometimes the plywood is sanded deeper on the soft part of the wood showing the harder part of the grain through the paint. Some of it is sanded so coarse you can see the texture of the sanding in the paint.
Chess Set / Screw Chuck Advice | Woodworking Talk
2022年10月28日 · 1- Make a wooden disc the exact size as the faceplate and affix it to the plate with the mounting screws. Screws entered through rear of faceplate. The wood protects your turning tools, if you accidentally make contact with the metal plate. I …
Thickness of plywood for bench seat which also stores books
2010年5月25日 · How thick should the horizontal plywood be to properly hold the books and people. Consider 1 person that is 190 lbs, a lady which is less than that, and a baby on board all sitting on the bench at once for instance. I have the impression 1/2" should be ok since there will be 1/2" ply vertically every 2' but I'd like to confirm with you all.