8 inch Disc sander-backing plate - The Home Shop Machinist
2010年2月21日 · There's no table, no shroud. Just a dangerous (and therefore fun) open spinning disc. (I could alternately use the screw on type discs, provided I could find stiff enough backing and the arbor. McMaster has an arbor that might work, but I couldn't find a backing plate.) I was hoping to find one magical source for all my sander building needs.
Disk Sander Cement - The Home Shop Machinist & Machinist's …
It stays tacky long enough for several discs. I use a full sheet of square paper on a 9" disc grinder, and cut the excess off -- it's a lot cheaper than 9" disc sheets. Another, much more expensive alternative is 3M 75 spray adhesive. It's pretty hard to find compared to the mundane 3M spray adhesives, but it's Feathering Disc Adhesive in an ...
Threading a 1" x 42" belt sander - The Home Shop Machinist
2009年4月8日 · Interior sanding is done either with or without the backing plate by following these steps that bypass and exclude the rear idler pulley: 1. Remove the Belt Sanding Table and the Belt Guards. 2. Feed the Sanding Belt through the workpiece and over the large upper idler wheel. Loosen the small upper wheel below it, swing it
Trunions for Disc Sander - The Home Shop Machinist
I think the idea's sound. The trunnions will be mounted either side of the disc. If he were to use ordinary bearings, then 1/4 of these would stick out, right where you want to slide longer lengths of wood across the face of the disc. I have a table saw from Startrite that uses a very similar principle for tilting the blade, and it works fine.
2" Inch Roloc grinder/sander? - The Home Shop Machinist
2023年1月20日 · I have never seen a dedicated roloc angle grinder. I use a lot of roloc discs and abrasives. I like the different arbors for different discs. Example, when using a 1" disc I like a 1" backing arbor. For a 3" disc a 3" backing arbor. And I made the mistake of buying a whole different locking system, still 3m but not roloc. So I needed an arbor ...
Is there an easy way to square the ends of 4" pipe?
disc sander I use my disc sander all the time for this type of work. Touch, roll, touch again, feeling while you go. If your sander table is flat and square I think you can hit square within .003" I suppose you could clamp a fence on the table to help since it is a big piece to handle. I keep a sacrificial vee block at the sander to help with ...
Cleaning up a 1/4" 4'x8' steel plate - The Home Shop Machinist ...
Something I have done, a floor scrubber, they can be fitted with scotchbrite, bristle, stainless wire and all sorts, they make short work of a big plate but take some practice controlling!, tilt one way to go fwd, the other back. Useful machine, you can get abrasive pads for them too, like a floor sanding edge sander.
Finished my 12" Disc Sander - The Home Shop Machinist
2008年2月12日 · 3/4 HP 3400 rpm motor scavenged from a combo belt/disc sander. Made the rest. The table is mild steel and the tooling slot matches my HF Tool Grinder so I can exchange tooling. I've already used the little miter gage. Table uses bicycle seat clamps, which work great: The bracket was rounded on the sander. The 80 grit wheel cuts that aluminum ...
Shop Made Tools - The Home Shop Machinist & Machinist's …
2017年3月2日 · The angle plate with it, my dad had made - all hardened, ground, square, parallel, and stress relieved: My friend also made these washer organizers out of 1/16 diameter stainless welding rod. The washers are from #10 to 5/16 to give you an idea of size, Sure makes them easy to keep track of:
decayed rubber on Rockwell 42 x 1" sander wheels?
Scishopguy: I use a lot of delrin in my work both as bearings and structurally. In this use I don't think the friction of the delrin is that much different than that of the wheels in my other 1" sander, which appear to be ABS or high impact styrene. However after looking at stock prices, the Delrin and 6061 alum in 1" plate are basically identical!